Special Offer BeneluxDecor TkRom INTERIOR PAINT CLASS 2 DAMASCO, wholesale Supreva, Tkrom

Description Matt plastic paint based on aqueous acrylic dispersion. Improved formula that minimizes spatter from roller painting. It is aimed at the professional sector, offering high quality finishes. With low content of VOC ́S and without ammonia. Technical sheet Technical data Classification in accordance with the UNE-EN 13300 standard. Matt gloss EN ISO 2813 Size of fine particles RO 21524 Resistance to friction in wet condition Class 2 ISO 11998 Additional technical data Theoretical coverage 10 -12 m2/l EN-ISO 23811 Density 1.570 ± 0.001 g/ml EN ISO 2811-1Viscosity 23000-25000 mPa.s (20 rpm, 23ºC)Solids in volume 42% ASTM D 2196-10Alchimi Berger 99 EN ISO 23811Classification according to fire performance B-s1, d0 UNE 48073GeneralThe surface must be compact, dry, free of dust, salts, loose or poorly adhering parts or any other type of contamination that could affect the adhesion of the system. The resistance of the substrate must be checked. Regardless of the substrate to be painted, the appearance must be homogenized and any differences in texture, gloss, absorption, etc. must be corrected. New works Substrate type: plaster mortar, plasterboard, concrete, fiber cement and other construction materials. Substrates under normal conditions: It is not necessary to apply a previous coat of primer. Highly porous and/or absorbent substrates: apply a coat of primer TK-5908 Tkrom Fijativo F4, to prevent excessive absorption during subsequent painting. Solid and smooth surfaces with low absorbency: Apply a coat of primer TK-5907 Tkrom Fijativo F1 beforehand. If the absorption power of the substrate is very low, it is recommended to sand the surface to open the pores. Restoration and maintenance Painted surfaces: Materials in bad condition must be completely removed and areas must be repaired until a healthy, dry and clean substrate is obtained. Old paints: it is recommended to apply a primer coat of TK-5907 Tkrom Fijativo Fijativo Penetrante F1, to strengthen the outer layer by creating a resin network which also allows perspiration, reduces absorption and facilitates subsequent painting. Aged, unpainted surfaces: The strength of the substrate should be checked. Powdery, sandy and/or highly absorbent surfaces. Apply a coat of TK-5908 Tkrom Fixador F4 primer to level and fix the substrate. Substrates with microorganisms: Remove mold and/or fungi by wet cleaning, apply one or two coats of TK-5905 Tkrom Tkrom cleaner reinforcement, leaving 12 hours between coats. If the damage to the substrate is very high, it is recommended to apply a primer coat of the sealing primer TK-5905 Tkrom Tkrom primer, following the manufacturer's instructions. Surfaces with efflorescence: Remove efflorescence and alkalinity with appropriate treatments, apply a coat of primer TK-5907 Tkrom Fijativo Fijativo penetrante F1. Application conditions Substrate temperature Min. +5ºC / Max. +35ºC / +35ºCAmbient temperature 5ºC / 35ºCSubstrate humidity Dry, damp substrate Dew point Substrate must be at least 3°C ​​above dew point to reduce the risk of peeling or efflorescence of the coating on walls and floors due to condensation. In conditions of high ambient temperature and low humidity, the likelihood of efflorescence on the product finish increases. Application instructions Method of application Can be applied by brush, roller and spray Can be applied by brush, short-hair roller or airless spray The second layer of product must be applied perpendicular to the first layer to achieve optimal opacity. Dilution Maximum dilution 10%. Dilutions higher than 10% will not allow the non-drip property to be obtained during application.Cleaning tools Clean tools with water immediately after use.Drying times Drying at 20°C and 65% relative humidity: The product does not stain after half an hour and can be recoated after 2-3 hours. The total drying time is 15-20 days. Additional information Not applicable when rain or frost is expected. Homogenize the product well before use. For any information regarding the safety aspects of the use, storage, transport and disposal of this product, users should consult the label and the latest version of the safety data sheet, which contains physical, ecological, toxicological and other relevant data. Material Safety Data Sheet: MSDS-5213 COD LER: 08 01 12 RESIDUES: NON-HAZARDOUS The EU VOC limit value for the product. Wholesale product available on the B2B marketplace, Supreva Market For Business, at wholesale prices directly from the importer.